产品概述：
水性金属防锈漆是以水做为分散介质，利用物理、化学等多重防锈机理配制而成，是传统金属防锈油漆的最佳换代产品。
产品特点：
1.卓越的环保安全性：无毒、无味、无污染、无三废，不燃不爆，确保了环境保护和消防安全，保障了劳动者的身体健康。
2.漆膜恒久性能优异 ：具有优良的耐盐雾、盐水、淡水、耐汽油、抗紫外光耐老化、耐高温、抗低温、耐湿热、耐温变等，具有很好的漆膜性能。
3.增效节能降低成本：可直接使用,不用涂刷底漆,省时省力、简便快捷，可大大提高工效，以水为稀释剂，产品利用率100%，单位涂装成本极低。
表面要求：
涂装前应检查被涂件表面是否彻底干燥，表面是否粘有油污灰砂等污物，被涂饰面不可有损伤，必须清除油污灰砂，底表面平整无损的条件下方可进行施工。
搅拌稀释： 应将漆浆充分搅拌均匀，如遇粘度过大，可适量加自来水稀释。
施工环境：
1、自然干燥：应选择晴天施工。环境温度5—40℃，相对环境湿度80%以下为佳，不适宜在3℃以下环境湿度大于80%条件下涂装，涂装后的漆膜4小时内应避免雨淋或用水冲洗。
2、烘干：为加速漆膜干燥，可进行烘干，烘烤温度不低于40℃，烘干时间不少于20分钟。
施工方法：
本产品适用刷涂、喷涂、浸涂。
涂装工具：
在施工过程中，必须单独使用涂装工具，不得和其它油漆或器具混用，用后用自来水清洗干净，以备反复使用。
施工用量：
涂刷一遍，1kg涂4-5㎡。
产品颜色：主要为铁红色和蓝色。
NBS Water-based metal Anti-rust Paint NBS-128 "Product Manual"
1. Product description:
The Water-based metal Anti-rust Paint is formulated with water as the dispersion medium, using multiple anti-rust mechanisms such as physics and chemistry. It is the best replacement product for the traditional metal anti-rust paint.
2. Features:
1) Excellent environmental protection safety: non-toxic, tasteless, non-polluting, no three wastes, non-flammable and non-explosive, ensuring environmental protection and fire safety, and protecting the health of workers.
2) Excellent film durability: It has excellent resistance to salt spray, salt water, fresh water, gasoline, ultraviolet light, aging resistance, high temperature resistance, low temperature resistance, damp heat resistance, temperature change resistance, etc., and has good paint film performance.
3) Increase efficiency, energy saving and cost reduction: it can be used directly without applying primer, saving time and effort, simple and fast, and can greatly improve work efficiency. Water is used as a diluent, product utilization rate is 100%, and unit coating cost is extremely low.
3. Surface requirements:
1)Before painting, check whether the surface of the painted part is completely dry and whether there is dirt, such as oily dust and sand, on the surface. The painted surface must not be damaged. The oily dust and sand must be removed. Construction can be carried out when the bottom surface is flat and undamaged.
2)Stirring and dilution: The paint slurry should be fully stirred evenly. If the viscosity is too high, it can be diluted with tap water in an appropriate amount.
4. Construction environment:
1) Naturally dry: sunny construction should be selected. The ambient temperature is 5-40℃, and the relative ambient humidity is below 80%. It is not suitable for painting under 3℃ and the ambient humidity is greater than 80%. The paint film should be protected from rain or washing with water within 4 hours after painting.
2) Drying: In order to accelerate the drying of the paint film, it can be dried, the baking temperature is not less than 40 ℃, and the drying time is not less than 20 minutes.
5. Construction method:
This product is suitable for brushing, spraying and dipping.
6. Painting tools:
During the construction process, the painting tool must be used alone, and must not be mixed with other paints or utensils. After use, it should be cleaned with tap water for repeated use.
7. Construction dosage:
Brush once, 1kg spread 4-5 square meters.
8. Product color: mainly iron red and blue.
